![]() Slide the relay back into its cover, dab a little super glue or tape it back together, and you’re ready to go. Be sure to get the pins hot and not just the solder. You may need to add just a little solder. Just dab a little flux on this joint and heat it with a soldering iron until it melts back together. One or two will probably have stress cracks. Get a magnifying glass and inspect these joints. There will be 2 plastic tabs holding it together. Look at the end of the flasher relay with the prongs sticking out. Find your perfect car with Edmunds expert reviews, car comparisons, and pricing tools. The following repair tip was provided by “tntguy”: Save up to 5,907 on one of 19,129 used 1996 Jeep Cherokees near you. The flasher is located in the Junction Block (under the dash, left of steering wheel. Refer to Ignition-Off Draw Fuse and Battery in the index in this service manual for the location of additional service information covering the ignition-off draw fuse and the battery. If a vehicle will be stored for more than about thirty days, the battery negative cable should be disconnected to eliminate normal IOD and, the battery should be tested and recharged at regular intervals during the vehicle storage period to prevent the battery from becoming discharged or damaged. When a vehicle will not be used for more than twenty days, but less than thirty days, remove the IOD fuse from the Power Distribution Center (PDC). However, it must be remembered that disconnecting the IOD connector will not eliminate IOD, but only reduce this normal condition. Simply disconnect the IOD connector from the JB receptacle slot # 15 and place it in slot # 11 (see diagram above). The IOD connector can be used by the vehicle owner as a convenient means of reducing battery depletion when a vehicle is to be stored for periods not to exceed about twenty days (short-term storage). The IOD connector feeds the memory and sleep mode functions for some of the electronic modules in the vehicle as well as various other accessories that require battery current when the ignition switch is in the Off position, including the clock. Ignition off draw fuse (IOD) / Vehicle storageThe term ignition-off draw identifies a normal condition where power is being drained from the battery with the ignition switch in the Off position. Ignition Run / Start – PDC (Power Distribution Center) Ignition Run / Heated seats / A/C Heater control / Flasher – Left and Right turn signal switch sense I hooked up to a trialer I had not hooked upto before. Overhead console, rear wiper, IP lights, rear flipper glass solenoid, power locks Note: On some or all WJ models, this fuse is also used for the ashtray light and the shifter assembly light. Grand Cherokee fusesįlasher, hazard switch (see Junction Block diagram above for location of turn signal Flasher relay – Mopar p/n 4686094)(Repair tip: WJ flasher repair) WJ Junction Block (under dash, left of steering wheel). Is something incorrect or missing? Please get in touch with us and we’ll fix it! We have organized as much information as we could find into a helpful table below. If you accidentally touch the glass part, wipe it off with rubbing alcohol before inserting it into your Grand Cherokee.Welcome to the in-depth page on the WJ Generation Jeep Grand Cherokee fuse diagram. Touching the new highbeam bulb will cause the bulb to burn out quicker. Highbeam bulbs grow dimmer by over 20% over time, therefore we recommend changing both bulbs on your Grand Cherokee at the same time, even if only one is burnt out - this will allow both high beam bulbs to have the same brightness on each side.īe careful not to touch the glass part of the new highbeam bulb with your finger when changing it on your Grand Cherokee. Replacing the bulb will restore functionality to both high and low beam functions. In some Jeeps your headlight and high beams are the same bulb – it is possible for the headlight portion of the bulb to burn out and for the highbeams to continue to function properly and vice versa. The high beam symbol in the dashboard on a 1999 Jeep Grand Cherokee is typically represented as a blue headlight icon with beams pointing outward. High beam lights can also be commonly referred to as a full beam whereas your headlights may be called the low beams. This video shows you how to change the highbeams, which are also known as brights or headlight high beam bulbs, in your 1999 Jeep Grand Cherokee.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |